Martes, Hunyo 26, 2012

Epson T10 - No Power

NO POWER in EPSON T10 - Troubleshooting



1. THE POWER SUPPLY -check the unit if there is an input voltage and output voltage by using a multitester.

Check all parts of the power supply, Capacitors, Diode, Fuse and  IC regulator






2. THE POWER SWITCH - Check the power switch button.



3. DIODE - Check the Main Board, see the image below, that diode is the common problem with Epson T10 printers, try to check it with multitester. you should know how to check a diode.





Pls post if you know other reasons for  this kind of problem.


Lunes, Hunyo 25, 2012

How to Install Waste tank in Epson T13



Install waste tank in your epson T13 printer


Same procedure as Epson T10 Heres the Link

How to Install Waste tank in Epson T10




Install waste tank in your epson printers,

1. Remove the Printers BodyCase, remove the screw







2. lift up the bodycase.  See the color white rubber tube at the back? Gently Pull it out.









3. Make a Hole in your Printers BodyCase.



4. Then insert the end of the rubber hole outside the Printers bodycase, then put back the bodycase and screw it



5. Get an empty bottle.







Linggo, Hunyo 24, 2012

RESET Canon IP 4680






FIRST STEPS:  Entering Service Mode
You have to enter in service mode in order to used the resetter. To do that follow this procedure,

1. Turn off the printer without pulling the power cords.
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Then Press Resume button twice then let BOTH buttons go.
5. You will notice that the Alternate Blinking error is gone, this means that the printer is in Service Mode state.

SECOND STEPS: Using the Resetter

1. After you download the resetter,  double click "IP4860.exe"
2. Press the "Main" Button, Then press "EEPROM Clear" button if a pop-up appear just click OK
5. Then power off the printer(sometimes you have to press twice the power button to turn off) and turn on again. and its done!

Download Resetter at Canon Resetter Page

RESET Canon IP 4760






FIRST STEPS:  Entering Service Mode
You have to enter in service mode in order to used the resetter. To do that follow this procedure,

1. Turn off the printer without pulling the power cords.
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Then Press Resume button twice then let BOTH buttons go.
5. You will notice that the Alternate Blinking error is gone, this means that the printer is in Service Mode state.

SECOND STEPS: Using the Resetter

1. After you download the resetter, double click "IP4760.exe"
2. Press the "Main" Button, Then press "EEPROM Clear" button if a pop-up appear just click OK
5. Then power off the printer(sometimes you have to press twice the power button to turn off) and turn on again. and its done!

Download Resetter at Canon Resetter Page

RESET Epson T13








Steps to Reset Waste Ink Counter in Epson
  1. Download Resetter Program for T13 (RAR file)!
  2. Extract the file
  3. Turn on the printer and connect the cable
  4. Click adjProg.exe to run program
  5. On License Agreement window, click Accept button
  6. Click Select button
  7. Select the printer model
  8. Select auto detection on Port menu
  9. Click Particular Adjustment Mode Select Maintenance>Waste Ink Pad Counter
  10. Click Check button to show the counter value
  11. Click Initialization button and wait until the operation is completed
  12. Turn off the printer when you order to do so
  13. Click OK button
  14. Wait until an order to turn ON the printer shows
  15. Turn ON the printer
  16. Click OK button
Download Resetter at Epson Resetter Page

RESET Epson T10




Steps to Reset Waste Ink Counter in Epson
  1. Download Resetter Program for T10 (RAR file)!
  2. Extract the file
  3. Turn on the printer and connect the cable
  4. Click adjProg.exe to run program
  5. On License Agreement window, click Accept button
  6. Click Select button
  7. Select the printer model
  8. Select auto detection on Port menu
  9. Click Particular Adjustment Mode Select Maintenance>Waste Ink Pad Counter
  10. Click Check button to show the counter value
  11. Click Initialization button and wait until the operation is completed
  12. Turn off the printer when you order to do so
  13. Click OK button
  14. Wait until an order to turn ON the printer shows
  15. Turn ON the printer
  16. Click OK button



Download Resetter at Epson Resetter Page